Cause Analysis Of Zero Loss In NC Machining Center

Apr 04, 2019

Leave a message

Case 1, one of the NC machining center, the "zero point loss" is reported, always in the change of the knife (time of the knife), or within 15 seconds after the change of the knife, but the zero point is not lost.

Because it always happens when the knife is changed, so check this section of the knife changing system, the induction switch, the position of the knife bank, the rectifier, the relay, the line, etc., are all not unusual, and have been on and off for a few weeks. Finally, in another battery found, abnormal battery voltage will also report such an alarm problem.


cnc plastic prototype with best price


Case 2 (focus!), Numeric Control Machining Center FANUC system Zero problem:

The causes of the problems in NC machining center are analyzed.

1. The zero point of machine tool in NC machining center system disappears, which may be caused by (APC) alarm caused by abnormal absolute pulse encoder.

2, see if the battery is dead, check the encoder cable short line, open the circuit, if unplugged, see if there is anything unusual about the axis removal signal.

3. The alarm number 300-349 shall be an absolute pulse encoder (APC) alarm, and the displayed alarm number and prompt information can be specifically displayed to determine the fault condition.

4, after troubleshooting, the NC machine tool can be returned to zero.

5, if the battery replacement, the use of non-power replacement, can be exempted from setting the origin.

The following are the basic steps for turning the NC machining center back to zero.

1, reinstall the batteries on the X-axis and Z-axis amplifiers respectively. Set the parameter 1815 ~ 5 to 1, and the zero-return mode is effective.

2, set the parameter 1815 to zero.

3, shake the X-axis, Y-axis and Z-axis to the point where you want to set it to zero, and then set the parameter 1815-4 to 1. 1.

4, power down the machine and power it up again.

5. The X-axis and the Z-axis are respectively shaken back to 100-mm in the hand-operated mode,

6, put the mode selection to return to zero mode, separately carry on manual zero return operation. When the return to zero is complete, the return-to-zero light of the corresponding axis will be lit. (after the manual zero return operation is complete, the X and Z axis return lights will be lit. Indicates zero position is set up. Then set the value of the soft limit: parameter 1320 and parameter 1321. The tool needs to be re-aligned before processing.)

Case 3, FANUC NC machining center, oi-MD, battery no alarm before the purchase of battery after too long, resulting in data loss, now start prompt to return to the reference point, and can not use unblocked block back to the reference point mode. You can set it to zero at any location by setting parameter No. 1815, but dare not go to the end of the stroke after setting it (because you don't know if the machine has a mechanical limit switch, Afraid to top to the two ends of the screw) see that set zero to reset the limit, but do not know the method. Z axis also dare not change the knife.

Solutions, 1. There are some machine tools equipped with hard limit switches, you can first remove the shield, and then shake the handwheel to a position similar to the hard limit and set it up, the setting of the knife arm will have some trouble, when changing, Need to shake the knife arm to the balance position, in addition to patience, a little parameter change, do not worry about the card machine, will succeed.

2, a large number of machine tools do not have a hard limit switch, and they are absolutely encoders that do not need to hit a block, including the height of the reference point of the change of knife is to be adjusted with professional tooling. In this situation, you can't just look at it with your eyes, and you can't just look at it with your eyes. Still need to find a professional, because the knife cylinder in the knife will push the knife a section of distance.


If you want to know more about wood cnc prototype service and cheap cnc prototyping plastic mode;. please email below.

steven@smilecnc-china.com (our sales manager)

Send Inquiry