Study On Production Technology Of Soft Deep Drawing Forming Steel Sheet For Automobile On Industrial Scale2

Apr 14, 2019

Leave a message

The sheet for automobile outer plate is required to be beautiful and has excellent sheet metal parts formability. In order to produce soft steel plates which can produce large deformation, carbon and impurities must be removed from the steel or harmless treatment should be carried out in the form of forming compounds to accurately control the crystal orientation of iron. On the basis of the soft principle and structure of the steel plate mentioned above, this paper introduces the technical development of the soft deep drawing forming steel plate for automobile based on the industrial scale production.

  

1.manufacture history of soft steel sheet

Deep drawing sheet steel sheet for automobile outer plate must have easy-to-work softness. The closer you get to pure iron, the softer it is. The main obstacle to making pure iron is carbon. The carbon and impurities in iron should be removed during the manufacture of soft steel plate, and a variety of techniques should be integrated to control the orientation of iron (atom) crystal and make it easy to process.

 

Firstly, low carbon steel was produced by adjusting the composition of molten steel to remove carbon and impurities in the steelmaking process, and then the orientation of iron crystal was controlled. Then the shape and material are adjusted in hot rolling and cold rolling, and the crystal orientation of iron is identical in the annealing process. At the same time, the dissolved carbon is fixed into carbides in order to realize harmless, thus the soft steel plate can be obtained. From the 350t molten steel produced by converter to the whole production process of finishing rolling into 0.8mm thickness sheet, the above-mentioned material control has been carried out all the time.

 

2.Annealing is the key to Crystal Control

Annealing is the most important process in the manufacture of deep drawing steel sheet. Because the cold rolled sheet becomes hard, it must be softened by annealing. This softening is a phenomenon known as recrystallization, which softens the hardened grains one by one in cold rolling. In order to improve the deep drawing property by annealing, the orientation of crystal arrangement is controlled by recrystallization, and the amount of solid solution carbon in the final product is reduced in order to restrain the aging deterioration of steel plate.

 

Annealing methods can be divided into "box annealing" (also known as gap or batch annealing) and "continuous annealing". The former has a long history and continues to be used today. Coil heating takes 1 day and cooling takes 3 days, which is slow and sufficient heat treatment. The latter from heating to cooling total 10min can be completed, is a high-efficiency continuous annealing. The difference between the two lies in the difference in the rate of heating and cooling.

When Al is combined with N in the full heating process of box annealing, only tetrahedral grains which can improve deep drawing formability are selected from recrystallized grains, so even the steel plate with higher carbon content can ensure good deep drawing formability. Moreover, due to the sufficient cooling, the carbon dissolved at high temperature can be fixed in the form of cementite, thus reducing the aging deterioration of the steel plate material. However, it takes 3 days and 4 days to anneal, and the heating and cooling of the coil also has the problem of poor uniformity.

 

 

3 improve the cooling after annealing to ensure the performance of vehicle outer plate

Car outer plate should ensure good workability, clean and beautiful surface, in addition to all kinds of defects, should also avoid stamping on the surface of the small wrinkles (also known as face strain).

Small amounts of C and N dissolved in steel, even at room temperature, flow everywhere in the steel, and during deep drawing deformation, they gather to the sliding deformation site and hinder the deformation of the steel plate. This phenomenon is called "aging". With the prolongation of time, the ductility or hardening of steel will deteriorate, that is, aging deterioration. If the steel plate is processed after aging, it will cause local deformation concentrated rib wrinkles and damage the appearance, and will lose the commodity value as the outside plate material of the automobile. In addition, if the steel plate hardened, stamped door handle will produce deformation and other folds. Therefore, in order to prevent aging deterioration caused by residual solid solution carbon in steel, it is necessary to make steel plate annealed without residual solid dissolved carbon. After annealing and cooling, Nippon Iron (Nippon Iron) was treated with "over-aging" to fix carbon into Fe3C and to treat it innocuously.

  

The so-called over-aging treatment is that after high-temperature annealing above 700 ℃ to control the crystal direction, many Fe3C seeds can be produced by rapidly cooling the steel plate to around 300 ℃. In a short period of time, the solid solution carbon in the steel can be aggregated to promote the growth of Fe3C. In order to obtain the Fe3C seeds, sulfides can be dispersed in the steel or cooling temperature can be lowered, so that the aging degraded steel can be continuously produced.

 

If you want to know more about stainless steel sheet metal products and brass sheet metal parts process. please email below.

steven@smilecnc-china.com (our sales manager)

Send Inquiry